ReferenceDesignLibrary

Refine Search

Eval Board Purpose Component Count + Extras Features Data Rate Design Author Main I.C. Base Part
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear All Selections Apply Filters

Designs (58)

58 Results - Page 1/6 |< < 1 2 3 4 5 > >|

EVAL-CN0160-EB1Z: Isolated USB Port

Manufacturer: Analog Devices Inc.

This application isolates a peripheral device that already supports a USB interface. Because the peripheral is not explicitly defined in this circuit, power to run the secondary side of the isolator has been provided as part of the solution. If the circuit is built onto the PCB of a peripheral design, power could be sourced from the peripheral’s off line supply, a battery, or the USB cable bus po…

View Design

EVAL-ADM2682EEBZ: Isolated RS-422/RS-485 & Power

Manufacturer: Analog Devices Inc.

The ADM2682E/ADM2687E evaluation board can be used for easy evaluation of the ADM2682E and ADM2687E power and signal isolated RS-485 transceivers. Screw terminal blocks provide convenient connections for the power and signal connections.

View Design

UMFT234XD-WE: USB 2.0 to UART

Manufacturer: FTDI, Future Technology Devices International Ltd

The UMFT234XD is a breakout board that converts USB2.0 Full-Speed to UART. These modules do not have a USB connector, instead, the modules plug directly into the USB host connector and the pads of the PCB makes electrical contact with the electrical contacts of the USB connector.

View Design

HD3SS6126: USB 3.0 KVM Switch

Manufacturer: Texas Instruments

This user's guide shows a USB 3.0 KVM switch application example of the HD3SS6126 device and provides recommendations for high-speed digital signal PCB design.

View Design

TIPD126: Bridge Sensor Conditioner

Manufacturer: Texas Instruments

This bridge sensor conditioner module delivers a well regulated current output to a ground-referenced load. The first stage uses a mixed-signal programmable gain amplifier (PGA) to provide linearization and temperature compensation to a differential bridge sensor voltage. The second stage converts the PGA output voltage into current and transmits the current over a standard 4 mA to 20 mA current …

View Design

TIPD108: PWM Signal Generator

Manufacturer: Texas Instruments

This circuit utilizes a triangle wave generator and comparator to generate a pulse-width-modulated (PWM) waveform with a duty cycle that is inversely proportional to the input voltage. An op amp and comparator generate a triangular waveform which is passed to the inverting input of a second comparator.

View Design

APP 4477: 1-Wire Bidirectional Voltage Translator

Manufacturer: Maxim Integrated

Devices such as FPGAs, microprocessors, the DS2482-100, and DS2480B are examples of 1-Wire master devices. The 1-Wire/iButton® slave devices are manufactured by Maxim and comprise an extensive family of parts that typically operate from 2.8V to 5.25V. The 1-Wire masters and slave devices have traditionally been 5V open-drain logic in the past.

View Design

ENC28J60-H: Ethernet Control Interface

Manufacturer: Olimex LTD

ENC28J60-H is world’s smallest Ethernet controller development board with its size of only 30x24 mm. It provides easy connection to any microcontroller with only a few parts via SPI which makes it perfect for adding Ethernet connectivity to embedded applications.

View Design

EVB_RT1710SGQW: Type-C Cable Identifier for Passive and Active Cables

Manufacturer: Richtek USA Inc.

The RT1710S is a Type-C cable ID for active and passive cables. All USB Full-Featured Type-C cables shall be electronically marked. Electronically marked cables shall support USB Power Delivery Structured VDM Discover Identity command directed to SOP'. This provides a method to determine the characteristics of the cable, e.g. its current carrying capability, its performance, vendor identification, etc.

View Design

FUSB302TGEVB: Type-C Interface Detection Solution

Manufacturer: ON Semiconductor

The FUSB302 evaluation board (FUSB302TGEVB) and included software allows customers a complete platform to evaluate the Type-C interface detection solution the FUSB302T provides. The evaluation board is designed for both stand-alone operation and connection to test equipment for specific testing requirements.

View Design
58 Results - Page 1/6 |< < 1 2 3 4 5 > >|