ReferenceDesignLibrary

Refine Search

Eval Board Voltage In Number of Motors and Type Power / Current Out Features Component Count + Extras Application / Target Market Design Author
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear All Selections Apply Filters

Designs (94)

94 Results - Page 1/10 |< < 1 2 3 4 5 > >|

DRV8662EVM: 50 ~ 200V Piezo Haptic Driver

Manufacturer: Texas Instruments

The DRV8662EVM Evaluation Module (EVM) is a fully-differential, high-voltage piezo actuator driver that provides quick response time for single layer and multi-layer piezo actuators. The DRV8662 drives piezo loads up to 200V differentially using an adjustable integrated boost converter. The evaluation module contains the DRV8662 piezo haptics driver, a programmable MSP430, and passive components …

View Design

EVAL6228QR: 1A, 8 ~ 52V in, Stepper Motor Driver

Manufacturer: STMicroelectronics

This application note describes the evaluation board of the DMOS fully integrated stepper motor driver L6228Q. The board implements a typical application that can be used as a reference design to drive two-phase bipolar stepper motors with currents up to 1 A DC.

View Design

DRV8840EVM: DC Motor Driver with Brake

Manufacturer: Texas Instruments

The DRV8840 evaluation module consists of a 5.0A, single-H-bridge motor driver with a Phase/Enable control interface and a small number external components that can be used to drive a single brushed DC motor. The on-board MSP430 MCU + software/GUI provides signaling and control and supports PWM speed control. With the DRV8840EVM, designers can quickly and easily evaluate the performance of DRV884…

View Design

DRV8843EVM: Dual DC Motor / Single Stepper

Manufacturer: Texas Instruments

The DRV8843 provides an integrated motor driver solution for printers, scanners, and other automated equipment applications. The device has two H-bridge drivers, and can be used to drive two DC motors, one stepper motor, or other loads. The output driver block for each consists of N-channel power MOSFET’s configured as H-bridges. The DRV8843 can supply up to 2.5-A peak or 1.75-A RMS output curren…

View Design

DRV8601ZQVEVM: ERM & LRA Haptic Driver

Manufacturer: Texas Instruments

The DRV8601 ERM/LRA driver evaluation module is a complete, low-power and ultra-fast turn-on driver for Eccentric Rotating Mass (ERM) and Linear Resonant Actuator (LRA) types of haptic actuators using a single-ended PWM input signal.

View Design

BD6212FP-EVAL-N: DC Brush Motor, 3 ~ 5.5V

Manufacturer: Rohm Semiconductor

This evaluation board has been developed for ROHM’s H-Bridge driver customers evaluating the BD62x2FP series. The BD62x2FP series can operate across a wide range of power supply voltages (from 3V to 32V max), supporting output currents of up to 2A. PWM signal control (20 kHz-100 kHz) or VREF control modes are used to vary motor rotation speeds.

View Design

BD6222FP-EVAL-N: DC Brush Motor, 6 ~ 15V

Manufacturer: Rohm Semiconductor

This evaluation board has been developed for ROHM’s H-Bridge driver customers evaluating the BD62x2FP series. The BD62x2FP series can operate across a wide range of power supply voltages (from 3V to 32V max), supporting output currents of up to 2A. PWM signal control (20 kHz-100 kHz) or VREF control modes are used to vary motor rotation speeds.

View Design

EVAL6470H-DISC: Dual 3A Stepper Driver, 8 ~ 45V in

Manufacturer: STMicroelectronics

The EVAL6470H-DISC can be used together with the STM32™ firmware library V1.0 and constitutes a complete motor control evaluation and a development platform.

View Design

DRV8308EVM: 13A, 8.5 ~ 32V in, 3-Ph BLDC

Manufacturer: Texas Instruments

This document describes how to use the DRV8308EVM to spin sensored brushless DC motors, as well as a tuning process for the DRV8308 speed control system.

View Design

DRV10970EVM: 1.5A, 3-Ph BLDC Hall, 5 ~ 18V in

Manufacturer: Texas Instruments

The DRV10970 EVM is an evaluation platform for the DRV10970 three-phase brushless DC motor driver.

View Design
94 Results - Page 1/10 |< < 1 2 3 4 5 > >|