ReferenceDesignLibrary

Refine Search

Eval Board AC Voltage Outputs and Type Voltage Out: Highest Current First Current Out Output Power Efficiency @ Conditions No-load Input Power @ Voltage Features Switching Frequency Internal Switch Component Count + Extras Voltage In Application / Target Market Design Author
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear
Clear All Selections Apply Filters

Designs (33)

33 Results - Page 1/4 |< < 1 2 3 4 > >|

STEVAL-ISA081V1: 12V @ 1A, 3.3V @ 100mA, 85~305Vin

Manufacturer: STMicroelectronics

(From User Guide) The purpose of this document is to provide information on the STEVAL-ISA081V1 switched mode power supply (SMPS) demonstration board. The STEVAL-ISA081V1 is an isolated SMPS capable of delivering a 12 W output over a wide input voltage range. It is designed for a mains application focused on providing a cost-effective and space-saving solution.

View Design

STEVAL-ISA004V1: 10W, 5V @ 1A, 12V @ 420mA

Manufacturer: STMicroelectronics

This evaluation board is an offline, wide-range, VIPer22A-E dual-output power supply with a switching frequency of 60 kHz and is set up for secondary regulation with an optocoupler. One output delivers 5 V at 1 A and a second output delivers 12 V at 0.42 A, making for a total output power of 10 W.

View Design

STEVAL-ISA062V1: 5.5W, 5V @ 500mA, 12V @ 250mA

Manufacturer: STMicroelectronics

This demonstration board is based on the new VIPer17H device, that is a converter that offers in one package a PWM controller built in BCD6 technology and a 800 V avalanche rugged vertical power section.

View Design

STEVAL-ISA013V1: 24W, 12V@1A, 5V@2.4A, 85~265VAC

Manufacturer: STMicroelectronics

This board is an off-line wide range dual output general-purpose power supply capable of delivering up to 24W through two outputs, +5V and +12V. The board is configured for secondary regulation with optocoupler feedback.

View Design

STEVAL-ISA022V1: 5.5W, 15V@200mA, 5V@500mA

Manufacturer: STMicroelectronics

The aim of the presented reference boards is to propose a power supply solution based on an offline discontinuous current mode flyback converter with isolation between input and output. The VIPer12AS incorporates the PWM controller with 60 kHz internal oscillator and altogether with the vertical power MOSFET switch in a SO8 package.

View Design

DER-191: 5V & 15V @ 2A, 40W, 90~265 VAC in

Manufacturer: Power Integrations

This engineering report describes an LCD Monitor power supply utilizing the TOPSwitch®-HX TOP256 from Power Integrations Inc.

View Design

RDK-531: 17.5W, 12V @ 1.25A + 5V @ 0.5A, 85 ~ 484VAC in

Manufacturer: Power Integrations

This document is an engineering report describing a 1.25A, 12V and 0.5A, 5V dual output embedded power supply utilizing the INN2904K, with a 900 V rated MOSFET, from the InnoSwitch-EP family of ICs.

View Design

STEVAL-ISA183V1: 12V/15V/5V @ 16W, 230 VAC

Manufacturer: STMicroelectronics

The STEVAL-ISA183V1 evaluation board implements a 16 W triple output power supply designed in quasi-resonant flyback topology,

View Design

STEVAL-ISA054V1: 100W, 3-Ph, 24V & 3.3V or 5V

Manufacturer: STMicroelectronics

This demonstration board introduces a solution for industrial power supplies. It takes advantage of the high voltage Power MOSFET, i.e. 1500 V breakdown voltage, to optimize the operation of the flyback converter based on the primary controller UC3844B.

View Design

STEVAL-ISA010V1: 12V & 5V @ 150mA Total, 85~500VAC

Manufacturer: STMicroelectronics

This document describes the STEVAL-ISA010V1 demonstration board, which is designed as an example of a simple non-isolated auxiliary power supply for a range of input voltages from 85 VAC to 500 VAC. There is an ever-increasing demand for small power supplies capable of working without voltage range limitations, even at nominal levels of 400 VAC and 415 VAC, respectively.

View Design
33 Results - Page 1/4 |< < 1 2 3 4 > >|