0.4mm Pitch, Type D Micro HDMI Spec Sheet Datasheet by Molex

View All Related Products | Download PDF Datasheet
) molex’ C REVISION. ECRIECN INFORMATION TITLE. SHEET No. EC No. DATE CONNECTOR DOCUMENT NUMBER CREATED / REVISED BY. CHECKED BY APPROVED BY PS-46765-003
PRODUCT SPECIFICATION
REVISION: ECR/ECN INFORMATION: TITLE: PRODUCT SPECIFICATION FOR
0.4mm PITCH, TYPE D MICRO HDMI
CONNECTOR
SHEET No.
9 EC No: S2011-0455
1 of 9
DATE: 2010/11/19
DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PS
-
4
676
5
-
003
SHANTH 2010/11/18 JESSIE 2010/11/18 NAGESH 2010/11/18
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
0.4mm PITCH, TYPE D, MICRO HDMI CONNECTOR
1.0 SCOPE
This Product Specification covers the 0.40 mm (.016 inch) centerline (pitch) printed circuit board
(PCB) connector series with selective gold and tin plating.
2.0 PRODUCT DESCRIPTION
2.1 PRODUCT NAME AND SERIES NUMBER(S)
Receptacle Assembly: Top Mount / Bottom Mount : 46765
Receptacle Assembly: Mid Mount / Offset Mid Mount Thru Hole: 46875 / 78580 / 78592 / 78587
& 78618.
Plug Assembly : 46770
DIMENSIONS, MATERIALS, PLATINGS AND MARKINGS
See the appropriate sales drawings for information on dimensions, materials, plating and
markings.
2.2 SAFETY AGENCY APPROVALS
UL File Number. TBA
CSA File Number.. TBA
3.0 APPLICABLE DOCUMENTS AND SPECIFICATIONS
EIA 364-1000
IEC 801
4.0 RATINGS
4.1 VOLTAGE
30 V
4.2 CURRENT
0.8 Amps @ 25°C
4.3 TEMPERATURE
Operating: - 30°C to + 85°C
Storage: - 40°C to + 85°C
) molex’ C PS-46765-003 ITEM REVISION. ECR/ECN INFORMATION TITLE. SHEET No. EC No. % CO N N ECTOR DOCUMENT NUMBER CREATED / REVISED BY. CHECKED BY APPROVED BY
PRODUCT SPECIFICATION
REVISION: ECR/ECN INFORMATION: TITLE: PRODUCT SPECIFICATION FOR
0.4mm PITCH, TYPE D MICRO HDMI
CONNECTOR
SHEET No.
9 EC No: S2011-0455
2 of 9
DATE: 2010/11/19
DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PS
-
4
676
5
-
003
SHANTH 2010/11/18 JESSIE 2010/11/18 NAGESH 2010/11/18
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
5.0 PERFORMANCE REQUIREMENTS
5.1 ELECTRICAL REQUIREMENTS
ITEM
DESCRIPTION TEST CONDITION REQUIREMENT
1a
Contact
Resistance
(Contacts)
Mated connectors
Contact: Measure by dry circuit and apply a
maximum voltage of 20 mV and a current of
10 mA. (Tested per EIA-364-06B)
Contact: 10 milliohms
MAXIMUM
[initial]
(After Subtracting Bulk
resistances of Plug,
Receptacle and their PCB
traces).
1b
Contact
Resistance
(Shield)
Mated Connectors
Shell: Measure by open circuit and apply
a maximum voltage of 5 V and a current of
100 mA. (Tested per EIA-364-06B)
Shell: 10 milliohms
MAXIMUM
[initial]
2 Insulation
Resistance
Unmated connectors
Apply a voltage of 500 VDC between
adjacent terminals or ground.
Mated connectors
Apply a voltage of 150 VDC between
adjacent terminals or ground.
Tested per EIA-364-21C
100 Megohms
MINIMUM (unmated)
10 Megohms
MINIMUM (mated)
3
Dielectric
Withstanding
Voltage
Unmated connectors
Apply a voltage of 250 VAC (RMS) for 1
minute between adjacent terminals or
ground
Mated connectors
Apply a voltage of 150 VAC (RMS) for 1
minute between adjacent terminals or
ground
Tested per EIA-364-20C, Method A
No breakdown;
current leakage < 1 mA
4 Contact Current
Rating
Test performed with all 19 Circuits Powered
55oC maximum ambient
85oC maximum temperature change
Tested per EIA-364-70A
0.3 A minimum
5 Applied Voltage
Rating
40 VAC (RMS) continuous maximum on any
signal pin with respect to the shield.
No breakdown;
current leakage < 1 mA
) molex’ C ITEM REVISION. ECRIECN INFORMATION TITLE. SHEET No. EC No. DATE CONNECTOR DOCUMENT NUMBER CREATED / REVISED BY. CHECKED BY APPROVED BY PS-46765-003
PRODUCT SPECIFICATION
REVISION: ECR/ECN INFORMATION: TITLE: PRODUCT SPECIFICATION FOR
0.4mm PITCH, TYPE D MICRO HDMI
CONNECTOR
SHEET No.
9 EC No: S2011-0455
3 of 9
DATE: 2010/11/19
DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PS
-
4
676
5
-
003
SHANTH 2010/11/18 JESSIE 2010/11/18 NAGESH 2010/11/18
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
6 Electrostatic
Discharge
Test unmated connectors from 1kV to 8kV in
1kV steps using an 8mm ball probe.
Tested per IEC-801-2
No discharge to contacts at
8kV
5.1 ELECTRICAL REQUIREMENTS (continued):
ITEM
DESCRIPTION TEST CONDITION REQUIREMENT
7
TMDS
Signals Time
Domain Impedance
Rise Time ≤ 200ps (10%-90%).
Signal to Ground pin ratio per HDMI
designation.
Differential Measurement Specimen
Environment Impedance
= 100 Ohm differential
Source-side receptacle connector mounted
on a controlled impedance PCB fixture.
Tested per EIA-364-108
Connector
100 Ohm ± 25%
Transition Area
100 Ohm ± 15%
Cable Area
100 Ohm ± 10%
8
TMDS
Signals Time
Domain
Cross Talk
(FEXT)
Rise Time ≤ 200ps (10%-90%).
Signal to Ground pin ratio per HDMI
designation.
Differential Measurement Specimen
Environment Impedance
= 100 Ohm differential
Source-side receptacle connector mounted
on a controlled impedance PCB fixture.
Tested per EIA-364-90
10%
MAXIMUM
) PS-46765-003 ITEM 0 REVISION. ECR/ECN INFORMATION TITLE. SHEET No. EC No. % CO N N ECTOR DOCUMENT NUMBER CREATED / REVISED BY. CHECKED BY APPROVED BY
PRODUCT SPECIFICATION
REVISION: ECR/ECN INFORMATION: TITLE: PRODUCT SPECIFICATION FOR
0.4mm PITCH, TYPE D MICRO HDMI
CONNECTOR
SHEET No.
9 EC No: S2011-0455
4 of 9
DATE: 2010/11/19
DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PS
-
4
676
5
-
003
SHANTH 2010/11/18 JESSIE 2010/11/18 NAGESH 2010/11/18
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
5.2 MECHANICAL REQUIREMENTS
ITEM
DESCRIPTION
TEST CONDITION
REQUIREMENT
9 Insertion Force
Mate and unmate connector at a rate of
25 ± 6 mm (1 ± ¼ inch) per minute.
Tested per EIA-364-13
44.1 N (10 lbf)
MAXIMUM insertion force
10a
Withdrawal Force
(Initial)
Mate and unmate connector at a rate of
25 ± 6 mm (1 ± ¼ inch) per minute.
Tested per EIA-364-13
5 N (1.1 lbf)
MINIMUM
25 N (5.6 lbf)
MAXIMUM
10b
Withdrawal Force
(After Durability)
Mate and unmate connector for 5,000
cycles at a rate of 25 ± 6 mm (1 ± ¼
inch)
per minute.
Tested per EIA-364-13
3 N (0.65 lbf)
MINIMUM
25 N (5.6 lbf)
MAXIMUM
11 Durability Mate connectors 5,000 cycles at a
maximum rate of 100 ± 50 cycles per hour.
Contact: 30 milliohms
MAXIMUM
(change from initial)
&
Shell: 50 milliohms
MAXIMUM
(change from initial)
12 Vibration
Amplitude: 1.52mm P-P or 147m/s2 (15G).
Sweep Time: 10-2000-10Hz in 20 minutes.
Duration: 12 times in each X,Y,Z axis.
Electrical Load: 100mA DC current applied
during test.
Tested per EIA-364-28, Condition III
Contact: 30 milliohms
MAXIMUM
(change from initial)
&
Shell: 50 milliohms
MAXIMUM
(change from initial)
&
Discontinuity < 1 microsecond
13 Shock
(Mechanical)
Pulse Width: 11msec
Waveform: half sine
Mate connectors and shock at 490m/s2
(50 G) in each of the X,Y,Z axis (3 shocks
in each axes)
Tested per EIA-134-27, Condition A
Contact: 30 milliohms
MAXIMUM
(change from initial)
&
Shell: 50 milliohms
MAXIMUM
(change from initial)
&
Discontinuity < 1 microsecond
) molex’ C PS-46765-003 ITEM REVISION. ECR/ECN INFORMATION TITLE. SHEET No. EC No. % CO N N ECTOR DOCUMENT NUMBER CREATED / REVISED BY. CHECKED BY APPROVED BY
PRODUCT SPECIFICATION
REVISION: ECR/ECN INFORMATION: TITLE: PRODUCT SPECIFICATION FOR
0.4mm PITCH, TYPE D MICRO HDMI
CONNECTOR
SHEET No.
9 EC No: S2011-0455
5 of 9
DATE: 2010/11/19
DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PS
-
4
676
5
-
003
SHANTH 2010/11/18 JESSIE 2010/11/18 NAGESH 2010/11/18
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
5.2 MECHANICAL REQUIREMENTS (continued)
ITEM
DESCRIPTION TEST CONDITION REQUIREMENT
14 Cable Flex
100 cycles in each of 2 planes
Dimension X = 3.7 x Cable Diameter
Tested per EIA-364-41C, Condition I
Dielectric Withstanding
Voltage:
No Breakdown at 150 VAC
&
Insulation Resistance:
At voltage of 150 VDC
between adjacent terminals or
ground.
10 Megohms MINIMUM
&
Discontinuity < 1 microsecond
15 Wrenching Strength
Mated Connectors
Apply a perpendicular force to a plug at a
15mm distance from the edge of the
receptacle.
Forces applied in 4 directions
(up, down, left, and right)
See Section 8.0 (Figures 1 & 2) for detailed
test set-up
0-20N
No Plug or Receptacle
Damage
&
20-40N
No Receptacle Damage
16 Cable Pull-Out
Apply an axial load to the cable for
1 minute
Tested per EIA-364-38C
40 N (9 lbf)
MINIMUM pullout force
Cable shall have no electrical
discontinuity
&
Cable shall have no
mechanical separation from the
connector
) PS-46765-003 ITEM REVISION. ECR/ECN INFORMATION TITLE. SHEET No. EC No. % CO N N ECTOR DOCUMENT NUMBER CREATED / REVISED BY. CHECKED BY APPROVED BY
PRODUCT SPECIFICATION
REVISION: ECR/ECN INFORMATION: TITLE: PRODUCT SPECIFICATION FOR
0.4mm PITCH, TYPE D MICRO HDMI
CONNECTOR
SHEET No.
9 EC No: S2011-0455
6 of 9
DATE: 2010/11/19
DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PS
-
4
676
5
-
003
SHANTH 2010/11/18 JESSIE 2010/11/18 NAGESH 2010/11/18
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
5.3 ENVIRONMENTAL REQUIREMENTS
ITEM
DESCRIPTION
TEST CONDITION
REQUIREMENT
17 Shock
(Thermal)
Mate connectors and expose to 10 cycles of:
-55°C for 30 minutes
+85°C for 30 minutes
Tested per EIA-364-32C, Condition I
Contact: 30 milliohms
MAXIMUM
(change from initial).
Shell: 50 milliohms
MAXIMUM.
(change from initial)
Visual: No Damage
18 Humidity
(Cyclic)
Mated Connectors:
Temperature: +25 to 85°C
Relative Humidity of 80 to 95%
Duration: 4 cycles (96 hours)
Note: Remove surface moisture & air dry for 24
hour prior to measurements.
Tested per EIA-364-31B
Contact: 30 milliohms
MAXIMUM
(change from initial)
Shell: 50 milliohms
MAXIMUM
(change from initial)
Visual: No Damage
Unmated Connectors
Temperature: +25 to 85°C
Relative Humidity of 80 to 95%
Duration: 4 cycles (96 hours)
Note: Remove surface moisture & air dry for 24
hours prior to measurements.
Tested per EIA-364-31B
Dielectric Withstanding
Voltage:
No Breakdown at 150 VAC
Insulation Resistance:
10 Megohms MINIMUM
Visual: No Damage
19 Thermal Aging
pre-conditioning
Mate connectors; expose to +105±2°C for 120
hours.
Note: Remove surface moisture & air dry for 2
hours prior to measurements.
Tested per EIA-364-17, Method A
Contact: 30 milliohms
MAXIMUM
(change from initial)
Shell: 50 milliohms
MAXIMUM
(change from initial)
Visual: No Damage
20 Thermal Aging
Mate connectors; expose to +105±2°C for 250
hours.
Note: Remove surface moisture & air dry for 2
hours prior to measurements.
Tested per EIA-364-17B, Condition 4, Method A
Contact: 30 milliohms
Maximum
(change from initial)
Shell: 50 milliohms
Maximum
(change from initial)
Visual: No Damage
) molex‘ C Ympeulurl Peak rm pcrllu": Human. [amperflure PrehnarYampnrarur: Room 'Em parllure Yimcro Pnk rempuuure 9w Vnmplrirun: Ramp Rm; mum Tempwralurv namn Rm.- nm u mum Yam perdum H rm .1 Po.- "mnemurl rm. wmm 5 ‘c a! Pe-k 1mm Ahnv: quuiflu: Tam pnrilum cm Dawn amp am w>i Description Requirement Averaqe Ramp Rate 3”C/sec Max Prehem Temperature 150°C Min to 200°C Max Preheat Time 60 to 180 sec Tum: Ramp lo Peak 3‘C/sec Max Trme over Liquidus (217’Cp 60 to 150 sec Peak Temperature 260 +0I—5°C Time with!" 5°C of Peak 20 to 40 sec Ramp - Cool Down G’C/sec Max Time 25”C to Peak 8 mm Max REVISION: ECR/ECN INFORMAWON: TITLE: SHEET No. EC No: DATE: CONNECTOR DOCUMENT NUMBER: PS-46765-003 CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PRODUCT SPECIFICATION
REVISION: ECR/ECN INFORMATION: TITLE: PRODUCT SPECIFICATION FOR
0.4mm PITCH, TYPE D MICRO HDMI
CONNECTOR
SHEET No.
9 EC No: S2011-0455
7 of 9
DATE: 2010/11/19
DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PS
-
4
676
5
-
003
SHANTH 2010/11/18 JESSIE 2010/11/18 NAGESH 2010/11/18
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
6.0 APPLICATION:
It is recommended to use Nitrogen in the reflow oven chamber
.
Recommended reflow profile:
) molex’ C Case (The upper Swde) ForSMDtype \ C‘earanos ofm 5mm .7 (Reference) C‘eamnce of a 15mm i (Reference) Ti _ /. Case
PRODUCT SPECIFICATION
REVISION: ECR/ECN INFORMATION: TITLE: PRODUCT SPECIFICATION FOR
0.4mm PITCH, TYPE D MICRO HDMI
CONNECTOR
SHEET No.
9 EC No: S2011-0455
8 of 9
DATE: 2010/11/19
DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PS
-
4
676
5
-
003
SHANTH 2010/11/18 JESSIE 2010/11/18 NAGESH 2010/11/18
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
7.0 PACKAGING
Parts shall be packaged in embossed tape to protect against damage during handling, transit and
storage.
See appropriate sales drawings on Sheet 1 for packaging descriptions.
8.0 GAGES AND FIXTURES
Figure 1
Test Set-Up for Wrenching Strength --- Normal µHDMI
Figure 2
Test Set-Up for Wrenching Strength--- Reverse type µHDMI
TEST SEQUENCE CHART REVISION. ECR/ECN INFORMATION TITLE. SHEET No. EC No. DATE CONNECTOR DOCUMENT NUMBER CREATED / REVISED BY. CHECKED BY APPROVED BY PS-46765-003
PRODUCT SPECIFICATION
REVISION: ECR/ECN INFORMATION: TITLE: PRODUCT SPECIFICATION FOR
0.4mm PITCH, TYPE D MICRO HDMI
CONNECTOR
SHEET No.
9 EC No: S2011-0455
9 of 9
DATE: 2010/11/19
DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PS
-
4
676
5
-
003
SHANTH 2010/11/18 JESSIE 2010/11/18 NAGESH 2010/11/18
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
1 2 3 4 5 6 7 8 9 10 11 12 13
Contact Resistance 1,4,6 1,4,6,8 1,4,6,8 2,7
Insulation Resistance 1,7 1,5
Dielectric Withstanding Voltage 2,6 2,4
Durability, Preconditioning 2 2 3 2
Durability 3 4
Thermal Aging, Preconditioning 3
Thermal Aging 3
Thermal Shock 3 4
Cyclic Temperature and Humidity 5 5
Thermal Disturbance
Vibration 5
Mechanical Shock 7
Reseating 5 7
Insertion and Withdrawal Forces 1,3,5,6
Cable Flex 1
W renching Strength 1
Cable Pull-Out 1
Current Rating 1
Applied Voltage Rating 1
Electrostatic Discharge 1
TMDS Signal Time Domain Impedance 1
TMDS Signal Time Domain Cross Talk FEXT 2
SAMPLES 5 5 5 5 5 5 5 5 5 3 3 3 3
Reliability Lab
Test
TEST SEQUENCE CHART

Products related to this Datasheet

CONN RCP MICRO HDMI 19POS SMD RA
CONN RCP MICRO HDMI 19POS SMD RA
CONN RCP MICRO HDMI 19POS SMD RA