AUD | USD

Datasheet

PRODUCT SPECIFICATION
REVISION: ECR/ECN INFORMATION: TITLE: PRODUCT SPECIFICATION FOR
MINI-FIT JR.
CONNECTOR SYSTEM
SHEET No.
E7 EC No: UCP2013-3729 1 of 10
DATE: 2013/04/01
DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PS
-
5556
-
001
NNGUYEN JBELL FSMITH
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
MINI-FIT JR.
Table of Contents
Section Page
1.0 Scope 2
2.0 Product Description 2
2.1 Names and Series Number(s) 2
Table 1 – Wire-To-Wire 2
Table 2 – Wire-To-Board 2
2.2 Dimensions, Materials, Platings, and Markings 2
2.3 Safety Agency Approvals 2
3.0 Applicable Documents and Specifications 2
4.0 Ratings 3
4.1 Voltage 3
4.2 Applicable Wires 3
4.3 Maximum Current Rating (Amperes) 3
Table 3 – Maximum Current Rating (Amperes)
Wire-To-Wire and Wire-To-Board 3
4.4 Temperature 3
4.5 Wave Solder Process Temperature 3
5.0 Wire-To-Wire Performance 4
5.1 Electrical Requirements 4
5.2 Mechanical Requirements 4
5.3 Environmental Requirements 6
6.0 Wire-To-Board Performance 7
6.1 Electrical Requirements 7
6.2 Mechanical Requirements 7
6.3 Environmental Requirements 9
7.0 Test Sequences 9
8.0 Packaging 9
9.0 Other Information 10
PRODUCT SPECIFICATION
REVISION: ECR/ECN INFORMATION: TITLE: PRODUCT SPECIFICATION FOR
MINI-FIT JR.
CONNECTOR SYSTEM
SHEET No.
E7 EC No: UCP2013-3729 2 of 10
DATE: 2013/04/01
DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PS
-
5556
-
001
NNGUYEN JBELL FSMITH
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
1.0 SCOPE
This Product Specification covers performance requirements for the MINI-FIT JR. 4.20 mm (.165 inch)
centerline (pitch) printed circuit board (PCB) connector series with Tin or Gold plating, and
The MINI-FIT JR. connector series terminated with 16 to 28 AWG wire using Crimp technology with
Tin or Gold plating.
2.0 PRODUCT DESCRIPTION
2.1 PRODUCT NAME AND SERIES NUMBER (S)
Table 1
WIRE
-
TO
-
WIRE
Description Series Number RoHS UL CSA TUV
Female Crimp Terminal 5556 Yes n/a n/a n/a
Receptacle Housing 5557 Yes Yes Yes Yes
Male Crimp Terminal 5558 Yes n/a n/a n/a
Plug Housing 5559 Yes Yes Yes Yes
Table 2
WIRE
-
TO
-
BOARD
Description Series Number RoHS UL CSA TUV
Female Crimp Terminal 5556 Yes n/a n/a n/a
Receptacle Housing 5557 Yes Yes Yes Yes
Vertical Header 5566 Yes Yes Yes Yes
Right Angle Header 5569 Yes Yes Yes Yes
Other products conforming to this specification are noted on the individual drawings.
2.2 DIMENSIONS, MATERIALS, PLATINGS AND MARKINGS
See the appropriate sales drawings for the information on dimensions, materials, platings and
markings.
2.3 SAFETY AGENCY APPROVALS
UL File: E29179
CSA Certificate: LR 19980
TUV Certificate: R72081037
3.0 APPLICABLE DOCUMENTS AND SPECIFICATIONS
See sales drawings and the other sections of this specification for the necessary referenced
documents and specifications.
Test Summary: TS-5556-002
PRODUCT SPECIFICATION
REVISION: ECR/ECN INFORMATION: TITLE: PRODUCT SPECIFICATION FOR
MINI-FIT JR.
CONNECTOR SYSTEM
SHEET No.
E7 EC No: UCP2013-3729 3 of 10
DATE: 2013/04/01
DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PS
-
5556
-
001
NNGUYEN JBELL FSMITH
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
4.0 RATINGS
4.1 VOLTAGE
600 Volts AC (RMS) (or 600 Volts DC)
4.2 APPLICABLE WIRES
Maximum Insulation Diameter
and
Applicable Wire Gauges
16 AWG: 3.10 mm / .122 inches MAXIMUM
18-24 AWG: 3.10 mm / .122 inches MAXIMUM
22-28 AWG: 1.80 mm / .071 inches MAXIMUM
4.3 MAXIMUM CURRENT RATING (Amperes)**
Note: PCB trace design may greatly affect temperature rise results in Wire-to-Board Applications.
** Ratings shown represent MAXIMUM current carrying capacity of a fully loaded connector with all circuits
powered. Ratings are based on a 30°C maximum temperature rise limit over ambient (room temperature).
Above charts are intended as a guideline. Current rating is application dependent. Appropriate de-rating is
required depending on factors such as higher ambient temperature, smaller copper weight of PCB traces,
gross heating from adjacent modules or components and other factors that influence connector
performance.
4.4 TEMPERATURE
Operating: * - 40°C to + 105°C
Nonoperating: - 40°C to + 105°C
*Including 30
°
C terminal temperature at rated current
4.5 WAVE SOLDER PROCESS TEMPERATURE
Headers with pegs: 240°C Maximum
Headers without pegs: 260°C Maximum
Table 3 - MAXIMUM CURRENT RATING (Amperes)
Wire-to-Wire and Wire-to-Board
Brass Phosphor Bronze
Ckt. Size
Wire 2 & 3 4 - 6 7 - 10
12 - 24 Ckt. Size
Wire 2 & 3 4 - 6 7 - 10 12 - 24
AWG #16 9 8 7 6 AWG #16 8 7 6 5
AWG #18 9 8 7 6 AWG #18 8 7 6 5
AWG #20 7 6 5 5 AWG #20 6 5 4 4
AWG #22 5 4 4 4 AWG #22 4 3 3 3
AWG #24 4 3 3 3 AWG #24 3 2 2 2
AWG #26 3 2 2 2 AWG #26 2 1 1 1
AWG #28 2 1 1 1 AWG #28 1 1 1 1
PRODUCT SPECIFICATION
REVISION: ECR/ECN INFORMATION: TITLE: PRODUCT SPECIFICATION FOR
MINI-FIT JR.
CONNECTOR SYSTEM
SHEET No.
E7 EC No: UCP2013-3729 4 of 10
DATE: 2013/04/01
DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PS
-
5556
-
001
NNGUYEN JBELL FSMITH
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
5.0 WIRE-TO-WIRE PERFORMANCE
5.1 ELECTRICAL REQUI
REMENTS
ITEM
DESCRIPTION
TEST CON
DITION
REQUIREMENT
1
Contact
Resistance
(Low Level)
Mate connectors: apply a maximum
voltage of 20 mV and a current of 100
mA. Wire resistance shall be removed
from the measured value.
10 milliohms
MAXIMUM
[initial]
2 Insulation
Resistance
Mate connectors: apply a voltage of 500
VDC between adjacent terminals and
between terminals to ground.
1000 Megohms
MINIMUM
3
Dielectric
Withstanding
Voltage
Mate connectors: apply a voltage of
2200 VAC for 1 minute between
adjacent terminals and between
terminals to ground.
No breakdown.
Current leakage < 5 mA
4
Temperature Rise
(via Current
Cycling)
Mate connectors. Measure the
temperature rise at the rated current
after 96 hours, during current cycling (45
minutes ON and 15 minutes OFF per
hour) for 240 hours, and after final 96-
hour steady state.
Temperature rise:
+30°C MAXIMUM
5.2 MECHANICAL REQUI
REMENTS
ITEM
DESCRIPTION
TEST CONDITION
REQUIREMENT
1
Terminal Mate
and
Unmate Forces
Per Circuit
Insert and withdraw terminal (male to
female) at a rate of 25 ± 6 mm (1 ± ¼
inch) per minute.
14.7 N (3.30 lbf)
MAXIMUM insertion force
and
0.5 N (0.11 lbf)
MINIMUM withdrawal force
2
Crimp Terminal
Retention Force
(in Housing)
Axial pullout force on the terminal in the
housing at a rate of 25 ± 6 mm (1 ± ¼
inch) per minute.
30 N (6.74 lbf)
MINIMUM retention force
3 Durability
Mate connectors up to 30 cycles at a
maximum rate of 10 cycles per minute
prior to Environmental Tests.
20 milliohms maximum
(change from initial)
PRODUCT SPECIFICATION
REVISION: ECR/ECN INFORMATION: TITLE: PRODUCT SPECIFICATION FOR
MINI-FIT JR.
CONNECTOR SYSTEM
SHEET No.
E7 EC No: UCP2013-3729 5 of 10
DATE: 2013/04/01
DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PS
-
5556
-
001
NNGUYEN JBELL FSMITH
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
5.2 MECHANICAL REQUI
REMENTS (
continued
)
ITEM
DESCRIPTION TEST CONDITION REQUIREMENT
4 Vibration
(Random)
Mate connectors and vibrate per EIA
364-28, test condition VII.
10 milliohms MAXIMUM
(change from initial)
and
Discontinuity < 1 microsecond
5 Shock
(Mechanical)
Mate connectors and shock at 50 g's
with ½ sine wave (11 milliseconds)
shocks in the ±X, ±Y, ±Z axes, (18
shocks total).
20 milliohms MAXIMUM
(change from initial)
and
Discontinuity < 1 microsecond
6
Wire
Pullout Force
(Axial)
Apply an axial pullout force on the wire
at a rate of 25 ± 6 mm (1 ± ¼ inch).
16 Awg = 88.0 N (19.8 lbf) Min.
18 Awg = 88.0 N (19.8 lbf) Min.
20 Awg = 59.0 N (13.3 lbf) Min.
22 Awg = 39.0 N (8.78 lbf) Min.
24 Awg = 29.0 N (6.52 lbf) Min.
26 Awg = 19.0 N (4.27 lbf) Min.
28 Awg = 9.80 N (2.20 lbf) Min.
7
Crimp Terminal
Insertion Force
(into Housing)
Apply an axial insertion force on the
terminal at a rate of 25 ± 6 mm (1 ± ¼
inch).
15.0 N (3.37 lbf)
MAXIMUM insertion force
8 Normal
Force Apply a perpendicular force.
Sn 1.47 N (150 grams)
MINIMUM
Au 0.49 N (50 grams)
MINIMUM
9 Panel Insertion and
Withdrawl Forces
Insert and withdraw a connector at a
rate of 25 ± 6 mm (1 ± ¼ inch) per
minute. (Applies only to plugs with
panel retention feature)
225 N (50.7 lbf)
MAXIMUM insertion force
and
157 N (35.3 lbf) MINIMUM
withdrawl force
10 Thumblatch
Operation Force
Depress latch at a speed rate of 25 ± 6
mm (1 ± ¼ inch) per minute. 16.67 N (3.75 lbf) MAXIMUM
11 Thumblatch Yield
Strength
Mate loaded connectors fully. Pull
connectors apart at a speed rate of 25 ±
6 mm (1 ± ¼ inch) per minute.
68 N (15.3 lbf) MINIMUM
PRODUCT SPECIFICATION
REVISION: ECR/ECN INFORMATION: TITLE: PRODUCT SPECIFICATION FOR
MINI-FIT JR.
CONNECTOR SYSTEM
SHEET No.
E7 EC No: UCP2013-3729 6 of 10
DATE: 2013/04/01
DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PS
-
5556
-
001
NNGUYEN JBELL FSMITH
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
5.3 ENVIRONMENTAL RE
QUIREMENTS
ITEM
DESCRIPTION
TEST CONDITION
REQUIREMENT
1 Thermal
Shock
Mate connectors: expose for 5 cycles
Between temperatures –55 and 105° C;
Dwell 0.5 hours at each temperature.
20 milliohms MAXIMUM
(change from initial)
Visual: No Damage
Dielectric Strength per 5.1.5
Insulation Resistance per 5.1.4
2 Thermal Aging Mate connectors; expose to:
96 hours at 105 ± 2°C
20 milliohms MAXIMUM
(change from initial)
and
Visual: No Damage
3 Humidity
(Steady State)
Mate connectors: expose to a
temperature of 60 ± 2°C with a relative
humidity of 90-95% for 96 hours.
20 milliohms MAXIMUM
Visual: No Damage
Dielectric Strength per 5.1.5
Insulation Resistance per 5.1.4
4 Cold Resistance
Mate connectors:
Duration: 96 hours;
Temperature: -40 ± 3°C
10 milliohms MAXIMUM
(change from initial)
and
Visual: No Damage
5 Mixed Flowing Gas EIA-364-65 with Class IIa Gas
concentrations (Gold plated only)
20 milliohms MAXIMUM
(change from initial)
and
Visual: No Damage
PRODUCT SPECIFICATION
REVISION: ECR/ECN INFORMATION: TITLE: PRODUCT SPECIFICATION FOR
MINI-FIT JR.
CONNECTOR SYSTEM
SHEET No.
E7 EC No: UCP2013-3729 7 of 10
DATE: 2013/04/01
DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PS
-
5556
-
001
NNGUYEN JBELL FSMITH
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
5.0 WIRE-TO-BOARD PERFORMANCE
6.1 ELECTRICAL REQUI
REMENTS
ITEM
DESCRIPTION
TEST CONDITION
REQURIEMENT
1
Contact
Resistance
(Low Level)
Mate connectors: apply a maximum
voltage of 20 mV and a current of 100
mA. Wire resistance shall be removed
from the measured value.
10 milliohms
MAXIMUM
[initial]
2 Insulation
Resistance
Mate connectors: apply a voltage of 500
VDC between adjacent terminals and
between terminals to ground.
1000 Megohms
MINIMUM
3
Dielectric
Withstanding
Voltage
Mate connectors: apply a voltage of
2200 VAC for 1 minute between
adjacent terminals and between
terminals to ground.
No breakdown.
Current leakage < 5 mA
4
Temperature Rise
(via Current
Cycling)
Mate connectors. Measure the
temperature rise at the rated current
after 96 hours, during current cycling (45
minutes ON and 15 minutes OFF per
hour) for 240 hours, and after final 96-
hour steady state.
Temperature rise:
+30°C MAXIMUM
6.2 MECHANICAL REQUI
REMENTS
ITEM
DESCRIPTION
TEST CONDITION
REQUIREMENT
1
Terminal Mate
and
Unmate Forces
Per Circuit
Insert and withdraw terminal (male to
female) at a rate of 25 ± 6 mm (1 ± ¼
inch) per minute.
14.7 N (3.30 lbf)
MAXIMUM insertion force
and
0.5 N (0.11 lbf)
MINIMUM withdrawal force
2
Crimp Terminal
Retention Force
(in Housing)
Axial pullout force on the terminal in the
housing at a rate of 25 ± 6 mm (1 ± ¼
inch) per minute.
30 N (6.74 lbf)
MINIMUM retention force
3 Durability
Mate connectors up to 30 cycles at a
maximum rate of 10 cycles per minute
prior to Environmental Tests.
20 milliohms maximum
(change from initial)
PRODUCT SPECIFICATION
REVISION: ECR/ECN INFORMATION: TITLE: PRODUCT SPECIFICATION FOR
MINI-FIT JR.
CONNECTOR SYSTEM
SHEET No.
E7 EC No: UCP2013-3729 8 of 10
DATE: 2013/04/01
DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PS
-
5556
-
001
NNGUYEN JBELL FSMITH
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
6.2 MECHANICAL REQUIREMENTS (continued)
ITEM
DESCRIPTION TEST CONDITION REQUIREMENT
4 Vibration
(Random)
Mate connectors and vibrate per EIA 364-28,
test condition VII.
10 milliohms MAXIMUM
(change from initial)
and
Discontinuity < 1 microsecond
5 Shock
(Mechanical)
Mate connectors and shock at 50 g's with ½
sine wave (11 milliseconds) shocks in the
±X, ±Y, ±Z axes, (18 shocks total).
20 milliohms MAXIMUM
(change from initial)
and
Discontinuity < 1 microsecond
6
Wire
Pullout Force
(Axial)
Apply an axial pullout force on the wire at a
rate of 25 ± 6 mm (1 ± ¼ inch).
16 Awg = 88.0 N (19.8 lbf) Min.
18 Awg = 88.0 N (19.8 lbf) Min.
20 Awg = 59.0 N (13.3 lbf) Min.
22 Awg = 39.0 N (8.78 lbf) Min.
24 Awg = 29.0 N (6.52 lbf) Min.
26 Awg = 19.0 N (4.27 lbf) Min.
28 Awg = 9.80 N (2.20 lbf) Min.
7
Crimp Terminal
Insertion Force
(into Housing)
Apply an axial insertion force on the terminal
at a rate of 25 ± 6 mm (1 ± ¼ inch).
15.0 N (3.37 lbf)
MAXIMUM insertion force
8 Normal
Force Apply a perpendicular force.
Sn 1.47 N (150 grams)
MINIMUM
Au 0.49 N (50 grams)
MINIMUM
9
PCB Engagement
and
Separation Forces
Engage and separate a connector at a rate
of 25 ± 6 mm (1 ± ¼ inch) per minute.
(Applies to parts with PCB retention features
only with PCB holes at nominal diameter)
49.0 N (11.0 lbf)
MAXIMUM insertion force
and
10.0 N (2.24 lbf)
MINIMUM withdrawal force
10 Pin Retention Force
Apply axial push force at the speed rate of
25 ± 3mm/minute.
9.81 N (2.20 lbf) MINIMUM
RETENTION FORCE
11 Thumblatch
Operation Force
Depress latch at a speed rate of 25 ± 6 mm
(1 ± ¼ inch) per minute. 16.67 N (3.75 lbf) MAXIMUM
12 Thumblatch Yield
Strength
Mate loaded connectors fully. Pull
connectors apart at a speed rate of 25 ± 6
mm (1 ± ¼ inch) per minute.
68 N (15.3 lbf) MINIMUM
PRODUCT SPECIFICATION
REVISION: ECR/ECN INFORMATION: TITLE: PRODUCT SPECIFICATION FOR
MINI-FIT JR.
CONNECTOR SYSTEM
SHEET No.
E7 EC No: UCP2013-3729 9 of 10
DATE: 2013/04/01
DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PS
-
5556
-
001
NNGUYEN JBELL FSMITH
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
6.3 ENVIRONMENTAL REQUIREMENTS
ITEM
DESCRIPTION TEST CONDITION REQUIREMENT
1 Thermal
Shock
Mate connectors: expose for 5 cycles
Between temperatures –55 and 105° C;
Dwell 0.5 hours at each temperature.
20 milliohms MAXIMUM
(change from initial)
Visual: No Damage
Dielectric Strength per 6.1.5
Insulation Resistance per 6.1.4
2 Thermal Aging Mate connectors; expose to:
96 hours at 105 ± 2°C
20 milliohms MAXIMUM
(change from initial)
and
Visual: No Damage
3 Humidity
(Steady State)
Mate connectors: expose to a temperature
of 60 ± 2°C with a relative humidity of 90-
95% for 96 hours.
20 milliohms MAXIMUM
(change from initial)
Visual: No Damage
Dielectric Strength per 6.1.5
Insulation Resistance per 6.1.4
4 Solderability Per SMES-152
Solder coverage:
95% MINIMUM
(per SMES-152)
5 Solder
Resistance
Dip connector terminals tail in solder:
Solder Duration: 5 ± 0.5 seconds;
Solder Temperature: 260 ± 5°C
Visual:
No Damage to insulator
material
6 Cold Resistance
Mate connectors:
Duration; 96 hours;
Temperature: -40 ± 3°C
10 milliohms MAXIMUM
(change from initial)
and
Visual: No Damage
7 Mixed Flowing Gas EIA-364-65 with Class IIa Gas
concentrations (Gold plated only)
20 milliohms MAXIMUM
(change from initial)
and
Visual: No Damage
7.0 TEST SEQUENCES
Testing sequences to be performed in accordance with EIA-364-1000.01
8.0 PACKAGING
Parts shall be packaged to protect against damage during handling, transit and storage.
Nylon parts should remain in there original packaging until ready for use to prevent moisture loss or
gain.
PRODUCT SPECIFICATION
REVISION: ECR/ECN INFORMATION: TITLE: PRODUCT SPECIFICATION FOR
MINI-FIT JR.
CONNECTOR SYSTEM
SHEET No.
E7 EC No: UCP2013-3729 10 of 10
DATE: 2013/04/01
DOCUMENT NUMBER: CREATED / REVISED BY: CHECKED BY: APPROVED BY:
PS
-
5556
-
001
NNGUYEN JBELL FSMITH
TEMPLATE FILENAME: PRODUCT_SPEC[SIZE_A](V.1).DOC
9.0 OTHER INFORMATION
9.1 GAGES AND FIXTURES
It is recommended that test plugs (Series 44281) be used for continuity testing of receptacles.
Standard mating parts should not be used for harness testing.
NOTE: The use of unauthorized testing devices and/or probes with a Molex product may cause
damage to and affect functionality of the Molex product, and such use may void any and all
warranties, expressed or implied.
9.2 CABLE TIE AND OR WIRE TWIST LOCATION
CKT Sizes Dim T Min.
Dual Row Single Row
2-6 3 .50” (12.7 mm)
8 4 .75” (19.1 mm)
10-12 5-6 1.00” (25.4 mm)
14-16 7-8 1.25” (31.75 mm)
18-20 9-10 1.50”(38.09 mm)
22-24 11-12 1.75” (44.45 mm)
The “T” dimension defines a “free” length of wire, or a length of wire that is not subject to
significant bias by external factors such as a wire tie, wire twisting, or other means of
bending or deforming of the wires that repositions them from their natural relaxed state
or location where they enter the housing. Wires are to be dressed in such a manner
to allow the terminals to float freely in the pocket. This dimension is a general recommendation
and may need to be adjusted for different wire gauges and wire type and insulation
thickness and insulation material.

Products

CONN SOCKET 18-24AWG CRIMP TIN
Available Quantity53879
Unit Price0.15
CONN PIN 18-24AWG CRIMP TIN
Available Quantity250640
Unit Price0.15
CONN SOCKET 16AWG CRIMP TIN
Available Quantity151809
Unit Price0.15
CONN SOCKET 18-24AWG CRIMP TIN
Available Quantity30430
Unit Price0.26
CONN SOCKET 18-24AWG CRIMP GOLD
Available Quantity7895
Unit Price0.66
CONN SOCKET 22-28AWG CRIMP GOLD
Available Quantity10764
Unit Price0.75
CONN SOCKET 16AWG CRIMP GOLD
Available Quantity7481
Unit Price0.86
CONN SOCKET 18-24AWG CRIMP GOLD
Available Quantity45279
Unit Price0.89
CONN RECEPT 2POS DUAL
Available Quantity73944
Unit Price0.41
CONN PIN 18-24AWG CRIMP GOLD
Available Quantity19886
Unit Price1
CONN RECEPT 4POS DUAL
Available Quantity6380
Unit Price0.47
CONN RECEPT 2POS VERT DUAL
Available Quantity22155
Unit Price0.48
CONN RCPT HSG 2POS BLK
Available Quantity37642
Unit Price0.5
CONN RECEPT 3POS VERT SINGLE
Available Quantity26307
Unit Price0.5
CONN PLUG 2POS VERT DUAL
Available Quantity38054
Unit Price0.53
CONN PLUG 4POS VERT DUAL
Available Quantity11307
Unit Price0.54
CONN PLUG 2POS PANEL MOUNT
Available Quantity13557
Unit Price0.56
CONN RECEPT 6POS DUAL
Available Quantity13638
Unit Price0.57
CONN RCPT HSG 4POS 4.20MM
Available Quantity12483
Unit Price0.6
CONN PLUG 4POS PANEL MOUNT
Available Quantity5361
Unit Price0.6